Modeling stability post zygomatic fracture reconstruction.

Zygomaticomaxillary complex (ZMC) fracture repair is one of the most common surgical procedures performed in craniomaxillofacial trauma management. Miniplates and screws are used to stabilize the fractured bone using small local incisions, however, these procedures are not infrequently associated with hardware-related post-operative complications. The amount of fixation hardware utilized varies depending on the fracture pattern and surgical judgment, with three-point fixation being the conventionally accepted treatment. However, limited experimental testing and clinical studies have suggested that ZMC stabilization may be achieved with less than three-point fixation. In this study, we utilized a previously developed finite element modeling approach that allows for detailed bone and muscle representation to study the mechanical behavior of the fractured craniomaxillofacial skeleton (CMFS) under one, two, or three-point fixation of the ZMC. Results suggest that using a miniplate along the infraorbital rim in three-point fixation increases the amount of strain and load transfer to this region, rather than offloading the bone. Two-point (zygomaticomaxillary and zygomaticofrontal) fixation yielded strain patterns most similar to the intact CMFS. One-point (zygomaticofrontal) fixation resulted in higher tensile and compressive strains in the zygomaticofrontal region and the zygomatic arch, along with a higher tensile strain on the zygomatic body. These modeling results provide biomechanical evidence for the concept of over-engineering in the stabilization of facial fractures. Furthermore, they support previous suggestions that less than three-point fixation of ZMC fractures may be adequate to achieve uneventful healing.

Rotation of a Part of the Composite Flap for Simultaneous Gonion Reduction and Malar Augmentation During Rhytidectomy in Asians.

BACKGROUND: The desired facial shape that Asians aim to achieve through plastic surgery differs from that of westerners. OBJECTIVES: The author facilitates facial volume deflation by using the rotation of a part of the composite flap to the malar area resulting in volumetric augmentation during rhytidectomy; simultaneously, a volumetric reduction was implemented in the gonion. METHODS: Extended deep plane rhytidectomy with the rotation of a part of the composite flap was performed in 49 patients, whereas extended deep plane rhytidectomy without the rotation of a part of the composite flap was performed in 20 patients. For the results, the satisfaction survey of the surgery was conducted in all patients and by 2 surgeons during a follow-up visit 12 months later. To assess the surgical outcome objectively, the author used the Allergan photometric midface volume deficit scale to measure the midface volume. The midface contour and degree of projection were analyzed using lateral view photographs of the patients. The measurement of segment CM (distance between the lateral canthus and mouth corner) and segment MA (distance from segment CM to the most protruding malar area) was performed. RESULTS: The patients who underwent extended deep plane rhytidectomy with the rotation of a part of the composite flap reported higher overall satisfaction and achieved more favorable results, as evaluated by the 2 aesthetic surgeons (P < 0.05). The scores on the Allergan photometric midface volume deficit scale showed a significant increase before and after the surgery in both groups (P < 0.05), also as evaluated by the 2 aesthetic surgeons. However, the change in scores was found to be higher in the extended deep plane rhytidectomy with the rotation of a part of the composite flap group. The midface contour and degree of projection showed an increase of 20.6% on the right face and 22.7% on the left face, respectively (P < 0.001). CONCLUSION: Using the rotation of a part of the composite flap during rhytidectomy resulted in overall satisfactory outcomes for all patients. Based on these findings, it can be concluded that the use of this surgical method is beneficial and effective.

Comparison of stress distribution around all-on-four implants of different angulations and zygoma implants: a 7-model finite element analysis.

BACKGROUND: In recent years, zygomatic implants and the all-on-four treatment concept have been increasingly preferred for rehabilitation of atrophic maxillae. However, debate continues regarding the optimal configuration and angulation of the implants. The aim of this study was to analyze the biomechanical stress in implants and peri-implant bone in an edentulous maxilla with zygomatic implants and the all-on-four concept, using multiple implant configurations. METHODS: A total of 7 models consisting different combinations of 4-tilted dental implants and zygomatic implants were included in the study. In each model, a total of 200 N perpendicular to the posterior teeth and 50 N with 45° to the lateral tooth were applied. A finite element analysis was performed for determination of stress distribution on implants and peri-implant bone for each model. RESULTS: Higher stress values were observed in both cortical and trabecular bone around the 45°-tilted posterior implants in all-on-four models when compared to zygomatic implants. In cortical bone, the highest stress was established in an all-on-four model including 45°-tilted posterior implant with 4,346 megapascal (MPa), while the lowest stress was determined in the model including anterior dental implant combined with zygomatic implants with 0.817 MPa. In trabecular bone, the highest stress was determined in an all-on-four model including 30°-tilted posterior implant with 0.872 MPa while the lowest stress was observed in quad-zygoma model with 0.119 MPa. Regarding von Mises values, the highest stress among anterior implants was observed in an all-on-four model including 17° buccally tilted anterior implant with 38.141 MPa, while the lowest was in the including anterior dental implant combined with zygomatic implants with 20,446 MPa. Among posterior implants, the highest von Mises value was observed in the all-on-four model including 30°-tilted posterior implant with 97.002 MPa and the lowest stress was in quad zygoma model with 35.802 MPa. CONCLUSIONS: Within the limits of the present study, the use of zygoma implants may provide benefit in decreasing biomechanical stress around both dental and zygoma implants. Regarding the all-on-four concept, a 17° buccal angulation of anterior implants may not cause a significant stress increase while tilting the posterior implant from 30° to 45° may cause an increase in the stress around these implants.

The accuracy of virtual surgical planning assisted management for L-shaped reduction malarplasty: A retrospective study.

This study aims to evaluate the accuracy of L-shaped reduction malarplasty with bone setback or resection on the zygoma and the mortice and tenon joint structure on the zygomatic arch under the guidance of virtual surgical planning (VSP). Adult patients with zygomatic protrusion or hypertrophy were enrolled and divided. L-shaped reduction malarplasty with or without bone resection and with the mortice and tenon joint structure on the zygomatic arch was conducted either by digital procedures comprising VSP and three-dimensional (3D) printing titanium templates (Group I) or by conventional methods (Group II). Positions of representative landmarks and superimposition models were analyzed by 3D cephalometry. Satisfaction rate and incidences of clinical complications were compared as well. Satisfactory reduction of zygomatic protrusion or hypertrophy was recognized among all 78 patients. Improved symmetry and great surgical accuracy were observed according to the cephalometry analyses. The bone segment movement of virtual plans and actual results in Group I were measured and showed no obvious difference for the inward movement (5.42 ± 0.98 mm vs. 5.33± 0.93 mm, P = 0.6906) and the sagittal overlap (4.77 ± 1.32 mm vs. 4.87± 1.21 mm, P = 0.7386) at the zygoma roots, along with the step length at the long-arm of the L-shaped osteotomy line (2.43 ± 1.11 mm vs. 2.39± 0.89 mm, P = 0.8665). The high resemblance between virtual plans and actual results was depicted via superimposition models. Meanwhile, a higher satisfaction rate (28 in 36, 78% vs. 20 in 42, 48%) and a lower incidence rate of complications (11 in 36, 31% vs. 21 in 42, 50%) were found in Group I. Within the limitations of the study it seems that the application of VSP in reduction malarplasty could significantly contribute to better surgical accuracy and reduced difficulties in the operation, which would be beneficial to patients with zygoma hypertrophy or prominence.

Novel Clinical Anatomical Consideration of the Superficial and Deep Layers of the Deep Temporal Fascia.

BACKGROUND: The deep temporal fascia provides anchoring during thread lifting, which is a minimally invasive face-lifting procedure. However, anatomical studies involving the deep temporal fascia in addition to effective and safe thread-lifting procedures are scarce. The authors clarified the anatomy of the superficial layer of the deep temporal fascia and its surrounding structure using ultrasonography, histologic sections, and cadaveric dissection to propose an effective thread-lifting procedure guideline. METHODS: The authors included 20 healthy young participants from the Republic of Korea. Real-time, two-dimensional, B-mode ultrasonography was performed. Longitudinal scanning was performed along three vertical lines: the line passing through the jugale, the anterior margin of the condylar process of the mandible, and the midpoint between the jugale and anterior margin of the condylar process. Histologic samples from three fresh adult cadavers were harvested from 2.5 cm above and below the zygomatic arch. Eighteen fresh adult hemifaces of cadavers from the Republic of Korea (six men and three women, aged 67.3 ± 7.2 years) were used to confirm the morphology of the deep temporal fascia. RESULTS: The superficial layer of the deep temporal fascia crossed the zygomatic arch and was connected to the origin of the zygomaticus major muscle at the line passing through the jugale. The superficial layer continued inferiorly to the parotidomasseteric fascia at the line passing through the midpoint and condylar process of the mandible. CONCLUSION: This study yielded the novel anatomy of the superficial layer of the deep temporal fascia, and this anatomical structure may be used for an ideal thread-lifting procedure.

Successful Reduction of Unilateral Zygoma Fracture Following Bilateral Malar Reduction Surgery.

Malar reduction surgery can increase its susceptibility to fractures in case of trauma. Patients who had malar reduction surgery and sustained a zygoma fracture pose unique challenges for treatment and management. This is a case of a 28-year-old female patient who presented with a unilateral zygoma fracture following bilateral malar reduction and augmentation rhinoplasty 6 years ago. Physical examination revealed a clicking sound when opening the mouth at the right zygomatic buttress and a depressed preauricular area, suggesting arch fracture. Computed tomography imaging demonstrated a loosened screw at the right zygomatic buttress and a depressed arch fracture. She wanted to remove all plates and treat her right fractured zygoma with absorbable materials. Through the bilateral intraoral incisions, the authors removed the plates and screws and reduced the depression with the Langenbeck elevator through the same right intraoral incision without fixation. The reduction was well-maintained without complications based on postoperative plain x-rays 1 month after surgery. She reported that the pain was mostly gone and that she did not hear any abnormal sounds when opening her mouth after the surgery. In this case, if the zygomaticomaxillary buttress is minimally displaced, but the zygomatic arch fracture is significantly depressed, the authors believe that fracture reduction with only an intraoral incision would be enough to achieve an optimal outcome. If the plates and screws used in the previous malar reduction are not well maintained, it may be necessary to remove them.

Peri-zygomatic complications on zygomatic implants with or without penetrating the external surface of zygoma: A 2-year retrospective study.

OBJECTIVES: The main purpose of this retrospective study was to assess the difference in the incidence of peri-zygomatic complications (PZCs) when zygomatic implants (ZIs) penetrate or do not penetrate the external surface of zygoma. MATERIALS AND METHODS: This study included 32 patients with edentulous maxillae or potentially edentulous maxillae undergo zygomatic implantation. The patients were divided into the penetration group (P-group) and the non-penetration group (N-group) according to whether the apex of implants penetrated the external surface of zygoma in postoperative CBCT. The extension length, the penetration section of the implants, and the skin thickness at the corresponding position were simultaneously measured. Clinical follow-up was conducted regularly until 2 years after surgery. The occurrence of PZCs (including peri-zygomatic infection, skin numbness, non-infectious pain, and foreign body sensation) was recorded. A mixed effect logistic model was used to compare the difference of complication rate between the P-group and the N-group, and odds ratio (OR) was calculated. Then identify the impact of the extension length, penetration section and skin thickness in P-group with the same model. RESULTS: A total of 71 ZIs were implanted in 32 patients, including 37 implants in the P-group and 34 implants in the N-group. During the 2-year follow-up, a total of 13 implants occurred PZCs, with an overall complication rate of 18.3%. Thereinto, the incidence rate was 29.7% in the P-group, and 5.9% in the N-group (OR = 6.77). In P-group, there was a significant difference in complication rate of different extension lengths, while the penetration section and skin thickness had no statistical significance on the complication rate. CONCLUSION: Under the limitation of this study, to minimize the risk of PZCs, ZI should be placed in a manner that avoids the apex penetrating the external surface of the zygoma.

Combining Patient-specific Implant With Malar Reduction to Repair Mid-facial Asymmetry Caused by Craniofacial Fractures in Asians.

Mid-facial asymmetry caused by bone defect or deformation resulted from craniofacial fracture was a common secondary complication needed to repair. Patient-specific implant (PSI) designed with the unaffected side as a template is a good choice to repair this kind of facial asymmetry. However, in Asians, the broad and prominent zygomatic bone in unaffected side is not an optimal template, because the oval facial shape was considered as a more attractive appearance in Asian esthetic concept. To repair the mid-facial asymmetry and to improve the facial contour, the authors combined PSI implantation with malar reduction in one-stage surgery. The authors referred the facial proportion index (the optimal ratio of mid and lower face was 1.27) as a basis for preoperative precise design to determine the ideal facial shape of unaffected side, and used mirror image overlay technique with the ideal shape of unaffected side as a template to design the PSI. With this surgical strategy, patients not only can repair facial asymmetry but also can get a more attractive appearance.

Anti-sagging Method in Reduction Malarplasty: Application of the Bracing System with the Preservation of the Zygomaticus Major Muscle Bony Attachment.

BACKGROUND: Cheek drooping after reduction malarplasty remains a concern for patients. OBJECTIVES: To evaluate the anti-drooping effectiveness of the bracing system technique with the preservation of the zygomaticus major muscle (ZMj) bony attachment and to determine the role of ZMj in anti-drooping. METHODS: A retrospective analysis was conducted of patients who accepted this method in our department from February 2016 to May 2021. Patients' subjective evaluation and two plastic surgeons' objective assessment of photographs were performed. The pre- and postoperative three-dimensional (3D) ZMj models were reconstructed and compared. ZMj length and tortuosity were also measured from 3D models. RESULTS: Twenty-two patients (44 ZMjs) met the inclusion criteria. Most patients (21/22, 95.45%) were satisfied with the postoperative appearance without ageing after reduction malarplasty, except for one feeling slightly older after the operation. The objective scoring results showed no deepening of the nasolabial fold in the majority (20/22, 90.91%) of patients. Two patients were one-grade worse, from score 1 to 2. Upward movement of the postoperative ZMj bony attachment was clearly observed compared with the preoperative 3D model. The significantly reduced ZMj tortuosity (p < 0.001) and the slightly increased ZMj length (not significant) after surgery supported the straightening of the ZMj which was also seen in the 3D comparison. CONCLUSIONS: The bracing system technique with preservation of the bony attachment of the ZMj is an effective and cost-effective anti-sagging method for reduction malarplasty. The ZMj was lifted and straightened after reduction malarplasty, which helped to prevent sagging. LEVEL OF EVIDENCE IV: This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266 .

Technique-Related Survival Rate and Complications of Zygomatic Implant Placement: A Systematic Review and Meta-Analysis.

PURPOSE: To assess the survival rate (SR) and probability of postoperative complications at both the implant and patient level for each of the four surgical techniques for zygomatic implant (ZI) placement: Brånemark, sinus slot, extrasinus, and extramaxillary. MATERIALS AND METHODS: A systematic literature review and meta-analysis of clinical studies that reported the survival rate and postoperative ZI complications for the rehabilitation of atrophic edentulous maxillae was conducted based on PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analyses) recommendations. Two independent reviewers consulted four databases during the literature search: MEDLINE (PubMed), Google Scholar, Clinicaltrials.gov, and LILACS. Duplicate articles were eliminated. RESULTS: A total of 35 studies were included in the meta-analysis. Subgroup analysis showed that study design (prospective vs retrospective) had no significant impact (P = .10) on the outcomes. The SR was highest for the Brånemark and extrasinus techniques (100%) and lowest for the sinus slot technique (94%; 95% CI = 86% to 102%). The extramaxillary (38%; 95% CI = 1% to 3%) and the Brånemark (29%; 95% CI = 15% to 44%) techniques resulted in the highest occurrence of patient-level complications. Moreover, the extramaxillary technique showed the highest percentage of prothesis-related complications (44%; 95% CI = 27% to 62%). CONCLUSIONS: ZI placement was demonstrated to be a reliable technique for the rehabilitation of severely atrophic maxillae, irrespective of the surgical technique evaluated. Accurate case and surgical protocol selection is of paramount importance to reduce technique-related postoperative complications.

Role of Intraoperative Imaging in Improving Closed Reduction of Zygomatic Arch Fractures: A Systematic Review and Meta-analysis.

PURPOSE: The use of intraoperative imaging (IOI) to improve the reduction adequacy of zygomatic arch (ZMA) fractures has been reported, but few systematic reviews have examined this topic. The aim of this review was to investigate and compare the value of IOI with conventional methods without IOI (N-IOI) for the closed reduction of ZMA fractures. METHODS: Electronic retrieval of MEDLINE, Embase, Cochrane Library, Web of Science, Scopus, and citation search until December 2, 2022, was used to identify controlled clinical trials that employed IOI for improving adequacy in closed reduction of ZMA fractures. The predictor variable was the use of IOI-yes/no (IOI vs N-IOI). The covariates included imaging technique (ultrasound, C-arm, and cone beam computed tomography) and ZMA fracture type (M-shape fracture, mechanistic force in 1 direction; variable fracture, mechanistic force in 2 directions). The primary outcome variables were the reduction adequacy of ZMA fractures (the remaining cortical step and dislocation angle) compared with the ideal mirrored position. Weighted or mean differences, risk ratios, and corresponding 95% confidence intervals were calculated, where P >.05 and I2＜50% fixed effect model was adopted, and a vice versa random effect model was adopted. RESULTS: A total of 1250 studies were identified, of which 6 studies with 259 participants were included. The meta-analysis results indicated that compared with N-IOI, IOI yielded fewer cortical steps (-1.76 [-2.42, 1.10], P ＜.00001, fixed model) and dislocation angles (-5.60 [-8.08, 3.12], P＜.00001, fixed model) in patients with variable ZMA fractures, while no significant difference was detected in the M-shape ZMA fracture (-0.72, [-2.93, 1.48], P = .52; -1.48, [-3.51, 0.55], P = .15). Although there was no significant difference in postoperative correction (0.35, [0.06, 2.01] P = .24, fixed model), all secondary revision cases occurred in the N-IOI group. Descriptive analysis showed that IOI yielded better symmetry and appearance satisfaction. CONCLUSION: IOI improved the adequacy of the procedure and led to a better postoperative appearance, especially for patients with variable ZMA fractures. Furthermore, the use of IOI avoided the risk of secondary surgery. In future studies, researchers should standardize the scale and outcomes to facilitate the intuitive evaluation of reduction adequacy.

The Value of Intraoperative Computed Tomography in the Treatment of Zygomatic Complex Fractures.

BACKGROUND: Due to the complex anatomical morphology and lack of anatomic markers on the surface of zygomatic complex (ZMC), the treatment results of ZMC fractures are often suboptimal. PURPOSE: The study aimed to evaluate the effectiveness of intraoperative computed tomography (ICT) in the treatment of unilateral ZMC fractures, and further study the feasibility of ICT to replace early postoperative Computed Tomography (CT). STUDY DESIGN, SETTING, AND SAMPLE: The investigators designed a retrospective cohort study. Adult patients who underwent surgery with unilateral ZMC fractures were enrolled. PREDICTOR VARIABLE: According to whether intraoperative CT was used, the subjects were divided into the ICT group and the control group (without ICT). MAIN OUTCOME VARIABLES: Five distances and 3 angles representing bilateral ZMC symmetry were main outcome variables. The differences of outcome variables were compared between the 2 groups and the indices of ICT group were further compared with their postoperative indices. COVARIATES: Demographics (eg age), etiology (eg traffic injury), dysfunction (eg diplopia), and surgical approach (eg vestibular incision) were collected as covariates while we conducted clinical investigation, examination, and implementation. ANALYSES: The data were analyzed using independent-samples t test, paired-samples t test, Mann-Whitney U test, and χ2 test. P value < .05 was considered statistically significant. RESULTS: A total of 60 patients (18 to 59 years) were enrolled in this study. All median values of the measurements in the ICT group were smaller than those in the control group, and the differences of horizontal displacement distance (0.56 vs 1.02 mm), anteroposterior displacement distance (1.69 vs 2.34 mm, 0.90 vs 2.35 mm), horizontal angle of bilateral zygomatic arch (2.31 vs 4.19°), and horizontal angle of bilateral zygomatic process (1.77 vs 2.94°) were significantly different between the 2 groups with P value < .05. Moreover, there was no statistically significant difference in all indices between the intraoperatively and postoperatively injured sides in the ICT group. CONCLUSIONS: ICT can improve the treatment outcomes of ZMC fractures by evaluating the fracture reduction adequacy during surgery. Moreover, ICT can replace early postoperative CT.

Stress distribution and displacement with four different types of MARPE on craniofacial complex: A three-dimensional finite element analysis.

BACKGROUND: Various designs of mini-implants assisted rapid palatal expander (MARPE) appliances can impact treatment effectiveness through their biomechanical effects. The purpose of the study was to study the stress distribution and displacement with four different designs of the MARPE appliance on the craniofacial complex. METHODS: A 3D finite element model of the craniofacial complex was created from CBCT DICOM data, comprising four distinct groups. Each group consisted of one 4-hole expansion screw positioned between the second premolar and first molar in all models. Group 1 used four single-cortical mini-implants (1.5×8mm) engaging only the palatal cortex. Group 2 employed four mini-implants (1.5×11mm) engaging both the palatal and nasal cortices. Group 3 had monocortical implants on the palatal slopes, while Group 4 was similar to group 3 with implants in the acrylic wings. Comparisons between groups were made for anchorage (groups 1 and 2), mini-implant position (groups 1 and 3) and surface effect (groups 3 and 4). Von Mises stresses and displacements at various skeletal and dental points were evaluated using ANSYS software. RESULTS: The highest stresses were observed in the maxillary, pterygoid and zygomatic bones, as well as in the mid- palatal suture in all four groups. Downward and forward rotation of the craniofacial complex was noted. Group 2 showed greater skeletal expansion than group 1. Among groups 1 and 3, group 3 showed a better stress distribution. Group 4 showed less dentoalveolar rotation than group 3. CONCLUSIONS: The MARPE appliances had an impact on the craniofacial complex with stresses on the mid-palatal suture, maxillary bone, pterygoid bones and anterior teeth. Clockwise rotation of the maxilla, zygomatic bones and dentition was noted, while the pterygoid bones and pterygoid suture were displaced backwards. MARPE with bicortical anchorage produces better skeletal expansion. Placing implants on the palatal slopes with acrylic wings results in better skeletal expansion with less clockwise rotation of the dentition.

Intraosseous venous malformation of the zygoma: Case report and pooled analysis.

The objective of this study is to provide a comprehensive summary of the clinical and radiological features of zygomatic intraosseous venous malformations (IVM), as well as its treatment strategies. The aim is to establish preoperative diagnostic bases that will aid in the identification of zygomatic IVM and facilitate the implementation of effective treatment. Four cases of pathologically diagnosed zygomatic IVM with typical clinical and radiological features were reported. They exhibited comparable clinical and radiological features, and the En bloc excision and reconstruction yielded satisfactory outcome. Pooled data analysis was performed with additional 74 cases collected from 63 previous studies. The results revealed a higher incidence of zygomatic IVMs in middle-aged females, with swelling, pain and ocular dysfunction being the typical clinical manifestations. The characteristic radiological features of these lesions were well-defined, round bony structures with specific internal trabecular patterns. A diagnostic flow-chart assisting the differential diagnosis of IVM was established. En bloc excision was deemed the most advantageous treatment option, as it presented minimal risk of haemorrhaging and no instances of recurrence. The decision to pursue reconstruction was contingent upon the extent of the defect. Alloplastic material has emerged as the most frequently employed reconstruction material in recent reports. The summarized characteristics of zygomatic IVM and the proposed diagnostic and treatment strategies, derived from the pooled analysis of reported cases, may help to improve diagnosis and management in further clinical practice.

Longitudinal reactions of maxillary sinus in patients treated with multiple zygomatic implants: A modified radiographic evaluation with clinical follow-up.

OBJECTIVES: To investigate the effects of zygomatic implant placement on the maxillary sinus using radiographic and clinical indicators. METHODS: Patients with an atrophic maxilla who underwent zygomatic implant placement were included. The thickness and morphology of the Schneiderian membrane (SM), infundibular obstruction, and posterior bone wall of the maxillary sinus were analyzed. The generalized estimating equation and chi-square tests were performed to compare the measurements. RESULTS: Fifty patients with 100 maxillary sinuses were included. In total, 148 zygomatic implants and 105 regular implants were placed in the maxilla. Overall, the mean pre- and postoperative SM thickness was 2.79 ± 3.26 mm and 3.97 ± 5.45 mm, respectively (p = 0.063). In sinuses with two zygomatic implants, the SM thickness increased significantly from 2.12 ± 2.14 mm preoperatively to 4.07 ± 6.14 mm postoperatively (p = 0.026). The number of sinuses with type IV morphology (fully radiopaque) increased from zero preoperatively to six (13%) postoperatively. Sinuses with a single zygomatic implant showed no difference in the pre- and postoperative SM thickness. Postoperatively, six sinuses had infundibulum obstructions. Postoperative osteitis of the bilateral sinuses was found in two patients. CONCLUSIONS: We have proposed a new imaging evaluation method and system for evaluating the maxillary sinus response. Preoperative infundibulum obstruction combined with mucosal thickening and double zygomatic implant placement are more likely to induce postoperative maxillary sinus mucositis and osteitis.

The surgical anatomy of the deep temporal nerve: A cadaveric study.

BACKGROUND: The aims of this study were to investigate the surgical anatomy of the deep temporal nerve (DTN) and find (fixed/static) anatomical landmarks that could be used during surgery to localise the DTN branches. METHODS: Ten hemifaces of Dutch cadavers were dissected at the Department of Anatomy of the Radboudumc. Landmarks and measurements of interest were number of branches of the DTN, distance from the tragus to the DTN, and distance from the cranial and caudal parts of the posterior root of the zygomatic bone until the DTN. RESULTS: In this cadaveric study, 10 hemifaces were dissected (male, n = 6 [60%]; female, n = 4 [40%]) with an equal left/right side division. The number of deep temporal branches varied from 2 (30%) to 3 (70%) per side. The mean distance to the tragus varied from 40 to 53 mm, with a mean distance of 44.3 ± 4.4 mm. The mean distance from the cranial part of the posterior root of the zygomatic bone to the DTN varied from 29 to 35 mm, with a mean distance of 31.3 ± 2.1 mm. The distance from the caudal part of the posterior root of the zygomatic bone to the DTN varied from 8 to 17 mm, with a mean distance of 13.4 ± 3.4 mm. CONCLUSION: This study investigated the surgical anatomy and landmarks used for identification of the DTN and its branches. It suggested using firm landmarks for nerve identification, such as the posterior root of the cranial and/or the caudal zygomatic bone.

Quantitative assessment of image artifacts from zygoma implants on CBCT scans using different exposure parameters.

This study was aimed at quantifying artifacts from zygoma implants in cone-beam computed tomography (CBCT) images using different exposure parameters. Two cadaver heads, one with two zygoma implants on each side and the other for control, were scanned using 18 different exposure parameters. Quantitative analysis was performed to evaluate the hypodense and hyperdense artifact percentages calculated as the percentage of the area. Hyperdense artifacts and hypodense artifacts were detected, followed by the calculation of the hyperdense and hypodense artifact percentages in the image. In the qualitative analysis of the artifacts, the scores used were as follows: absence (0), moderate presence (1), or high presence (2) for hypodense halos, thin hypodense lines, and hyperdense lines. Artifact analysis was performed qualitatively and quantitatively using the post-hoc Tukey and Two-way ANOVA tests. As a result, in the qualitative analyses, zygoma implants showed a significant difference compared to the control group with regard to hyperdense and hypodense artifacts (p < 0.05). There was a significant difference between the means according to the FOV size arithmetic averages (p < 0.05). In terms of voxel size, the difference was found to be significant, where 400 microns showed the highest hypodense artifact while 200 microns showed the lowest hypodense artifact. In conclusion, hypodense and hyperdense artifacts were significantly higher in cadavers with zygoma implants than in controls. As FOV and voxel size increase, more hypodense artifacts are produced by zygoma implants so smaller FOV and voxel sizes should be used to prevent poor image quality of adjacent teeth.

Histological and Immunological Evaluation of the Osteogenic Effects of Compact Bone-Delivered Stem Cell on Spongiosis Bone in the Rat Zygomatic Arch Defect Model.

BACKGROUND: In stem cell applications, apart from bone marrow and adipose tissue, compact bone is also used as an alternative. However, studies on this subject are limited. In our study, we investigated the effect of stem cell derived from compact bone on rat zygomatic arch defect. METHODS: Fifteen rats were included in the study. Five rats were killed to obtain stem cells before the experiment. The rats were divided into 2 groups with 5 rats each. In group 1, compact bone-derived stem cell was applied. In group 2, adipose tissue-derived stem cell was applied. Right zygomatic arch defect was created in rats in both groups. Zygomatic bones were decellularized by cryosurgery. Stem cells were transferred to zygomatic bones. The number of stem cells, stem cell differentiation, and superficial markers obtained from the groups were examined. Histologically, cell structure, osteocyte count and osteopontin scores, elemental composition of the groups, percentages of resemblance to intact bone, osteocytes numbers, and cells were examined by electron microscopy of the bones in the groups after killing. RESULTS: The number of stem cells administered to the groups was 5 × 107 and 3.2 × 107 for group 1 and group 2, respectively (P > 0.05). Histologically, the morphology of the cells in group 1 was found to be healthier than group 2. The number of osteocytes was 97.56 ± 15.4 and 132.93 ± 10.8 in group 1 and group 2, respectively (P < 0.05). The osteopontin score was 3.47 ± 0.73 and 65 ± 0.64 in group 1 and group 2, respectively (P < 0.05). In the electron microscope examination, the morphologies of the cells in group 1 were seen more normal. The Ca/P ratio of the groups was 1.51 and 1.59 in group 1 and group 2, respectively (P > 0.05). Osteocyte counts were 10.7 ± 2.8 and 6.1 ± 1.2 in group 1 and group 2, respectively (P < 0.05). Morphological similarity percentages to normal bone were 88.4% and 79.6% in group 1 and group 2, respectively (P > 0.05). CONCLUSION: Stem cells obtained from compact bone gave positive results in zygomatic arch defect. This method can also be used as an alternative in stem cell applications.

Comparative Outcomes of Malar Implants Versus Fat Transfer to Cheeks Among Transfeminine Individuals Undergoing Malar Augmentation.

BACKGROUND: Malar augmentation is a key procedure sought out by transfeminine individuals seeking to feminize their facial appearance. Different surgical techniques have been described in the literature including fat transfer to the cheeks and malar implant placement. Because of the paucity of information in the literature, there is no consensus on best practices for this procedure. The objective of our study is to determine the effectiveness and safety of malar implants as compared with fat transfer to the cheeks in transfeminine individuals. METHODS: We examined all patients with the diagnosis of gender dysphoria that were referred to the senior author seeking consultation for feminizing facial procedures between June 2017 and August 2022. Patients who underwent fat transfer to the cheeks or malar implant placement were included in our study. We reviewed the electronic medical record of each patient, and we retrieved and analyzed data regarding demographics, medical and surgical history, operative dictations, clinic notes, and postoperative follow-up. Univariate analysis was used to assess for differences in postoperative complications between these 2 groups. RESULTS: We identified 231 patients underwent feminizing facial gender affirming surgery, with 152 patients receiving malar augmentation through malar implants or fat grafting. One hundred twenty-nine patients (84.9%) underwent malar implant placement and 23 (15.1%) underwent fat grafting to the cheeks. The mean follow-up time was 3.6 ± 2.7 months. Patient satisfaction was greater in the malar implant group (126/129, 97.7%) compared with the fat transfer group (20/23, 87%, P < 0.045). Two patients who received implants (1.8%) experienced postoperative complications. No patient undergoing fat transfer experiences similar adverse outcomes. Nevertheless, the difference was not statistically significant (P = 1.00). CONCLUSIONS: Our findings support the contention that malar implants are a safe alternative for malar augmentation among transfeminine individuals. While autologous fat transfer to the cheek is an indispensable option in patients requiring minor malar enhancement, malar implants offer a more permanent option with a better aesthetic outcome in patients requiring major malar enhancement. To minimize postoperative complications, surgeons should emphasize patient compliance with postoperative directions.